У нас вы можете скачать книгу cutting 2 инструкция в fb2, txt, PDF, EPUB, doc, rtf, jar, djvu, lrf!

It is possible to set that it will cut to the area outside of the push rollers, or not to cut at the ends of the media. Default setting is to the internal edge of the push rollers. It can be set up to 10 mm outside positive value or 10 mm inside negative value from the default position. Setting Mirror There is a function to mirror the cutting by reversing the origin point and coordinate axes. Reference This setting will be saved even if the power is shut off.

Supplement Press the [2] key OFF to turn off the mirror. Supplement Do not send new data to plotter while copying. Cutting data in the buffer memory will be cleared. Previous cutting data will be cleared and newly sent data will be stored as cutting data if you send new data with 10 seconds or more interval from the time it finished cutting.

Cutting data is stored in the buffer memory. Choosing to change media will instantly detect the media and proceed to a copy area cut. Media switch copies can be made up to the set copy number designated number. Operation 1 Create one data you want to copy.

Panel Cutting To prevent long skew, utilize partition length when cutting. Supplement When Partition Pastern is on, the machine will begin by dividing up partition length and continue cutting until one of the following data breaks appears. When the first partitioned area cut is finished, the machine will move to the next area, and repeat this until all areas have been cut. Registration mark reading accuracy when a designated registration mark is being read by this machine is within 0.

The area necessary to scan the registration mark when the mark distance is set is as following: Do not print in the shaded area shown in the Figure below. Position of the Origin Point and the Registration Mark The origin point after scanning the registration mark will be as shown below. Media That Registration Mark Cannot be Detected It may be hard to scan the registration mark as following, depending on the media conditions. Transparent media Registration mark cannot be scanned because the cutting mat surface is also read in.

Registration mark other than black line on white background Sensitivity of the sensor is based on the registration mark written in black on white background.

But if there are many registration marks, it will take longer to detect, and the area that can be cut becomes smaller. A function to continuously cut the print with same design aligned, Supplement using a plugin for the Illustrator. It is appropriate for cutting multiple Setting is only possible from the Graphtec numbers of stickers or similar. It cannot be set on the plotter. Push the [FAST] key to change the setting digits. Setting Mark Distance Mark distance is set so it will not perform detection of the location where the registration marks are not present.

This allows to scan the registration marks faster, and also prevents malfunction by the dirty media. X AXIS setting screen is displayed. Digits of settings can be changed by pressing the [FAST] key. Setting range is from 0. Setting Distance Adjustment Between the Registration Mark It will adjust the cutting if the distance between the registration marks are different from the original value on the data using the ratio calculated from the difference.

This is called distance adjustment between registration marks. The default offset for the registration mark is 0. Setting range is from Adjusting the Sensor Level Scan level threshold value between the media background color and registration mark of the sensor scanning the registration mark is automatically adjusted.

Sensor is adjusted to scan the registration mark written in black lines on white background. Readjust the scan level of the sensor depending on the color and gloss of the media. Supplement Following message is displayed. Manually Adjusting the Sensor Level Threshold Value Scan level threshold value between the media background color and registration mark of the sensor scanning the registration mark is set.

Adjust the scan level of the sensor depending on the color and gloss of the media. Setting range is from 30 to The tool carriage moves in the Y direction, while the media movies in the X direction. Raising the numerical value in the following situations will allow you to detect a registration mark.

Test the Registration Mark Sensor If there still is a difference in the cutting, even after performing an CAUTION adjustment using the registration mark, it is possible to check if there This function performs cutting after the is a problem with the registration mark itself or the application by registration mark is scanned.

Setting Speed of the Registration Mark Scan Speed of the tool carriage and media to scan the registration mark is set. It may not scan the registration marks or the difference may become large when the speed is too high, but the cutting time becomes longer when the speed is too slow.

Adjusting for the Registration Mark Scan Position Sensor to scan the registration mark is positioned away from the tip of the tool pen tip. Therefore, it is necessary to adjust the coordinate values of the scanned registration mark so it will match with the cutting position. Confirm that the tool is at the position shown in the left image grey square area , and press the [ENTER] key.

It will read the registration mark, and then plot the registration mark for comparison. Set the Y value measured in step There are following 3 methods depending on the number of registration marks scanned.

In general, the adjustment becomes more accurate with more registration marks scanned, but it will take longer to adjust. This adjustment is called 2 axis adjustment tilt adjustment. If the loaded media is tilted as shown below, position of the scanned registration mark is shifted from the position where it should be. X and Y axes and the distance between each of the registration marks. It will perform 2 axes warp adjustment in addition to the 2 axes tilt adjustment and distance adjustment, so it can adjust more precisely than other methods.

Adjust Automatically This section describes the operation to adjust with registration mark Supplement scan by moving to registration mark automatically after setting the See "Adjust Manually" if you are P. Input value initially same as measured value is displayed under that. If the input value is not changed, it will assume that there is no difference between measured distance and the distance in the data. Size and position of the registration scan start area is same for Point Point Repeat steps 4 and 5 if a message Registration marks are scanned.

A message to move to next registration prompting to move to next registration mark mark position is displayed once the scanning is completed.

Manual Position Adjust Here, we will explain how to match up points while manually confirming the media and tool cutter pen or plotting pen points. The ARMS function cannot be used for accurately matching up points.

The distance between each points can also be entered to adjust the distance. Manual Position Adjust Method of manual position adjust is described here. Supplement Adjustment will be cleared if following is done after setting the adjustment. Set the rotation or mirror prior to the axis adjustment Axis adjustment will convert in accordance with rotation or mirror in this case. Repeat steps 12 and 13 if following message prompting to move to the adjustment mark is Once all the adjustment marks are specified, DISTANCE entry screen is displayed.

Setting Regarding Cutting Quality There are times that ideal cutting may not be possible, such as the lines may shift, corners deform, or uncut sections occur, due to the characteristics of the media thickness, how hard it is, etc. To cut the corner of thick media sharply Outline of Tangential Emulation The blade needs to be facing toward the direction of cut when cutting the media. The tip of the blade is shaped as shown so the blade is facing the cutting direction even when it is cutting curved lines or corners.

Setting Length of the Overcut Set the length of overcut with tangential emulation. Setting of the Initial Down Force The initial down-force setting is effective when tangential mode is selected. Tangential control is generally used for the cutting of thick media. With thick film, additional time is required for the cutter blade to penetrate the media fully, even when the necessary cutting force is applied.

The cutting operation starts before the cutter blade has fully penetrated the media, causing uncut sections to be left. Setting the Step Pass It may not cut the curved line smoothly if there is very short lines in the curve. It will cut in the units of the specified value when the STEP PASS is used, which allows to control the short lines with certain length, resulting to stable rotation of the blade for higher cut quality.

Setting the Offset Angle The CE analyzes the cutting data, and controls the angle of the cutter blade tip if the change in the angles of the corner is large.

Angle control is applied if there is larger angle change than the angle specified as reference angle. The time to cut is shortened by setting large value for the reference angle, since it will only apply blade control when there are angles with large angle change, hence reducing the time to make the blade control. Setting range for adjustment value is Press the [FAST] key to change the setting digits.

Setting Initial Blade Control Position Adjust After turning on the power or changing pen condition settings, touch the blade to the media and adjust the blade direction.

The Initial Blade Control Position will need to be set in order to make sure the area is not damaged and that the blade properly makes contact with the media. Paper-weight is located under the tool carriage.

Settings Regarding Cutting Time Time necessary for cutting depends on the speed to move the tool and media, and efficiency of the operation. It is best to cut slowly and carefully to cut precisely, but the speed is required to enhance the operational efficiency.

Sorting the Cutting Data Sorting the cutting area parameter data will increase cut efficiency by minimizing time spent by media movement and by grouping cutting to happen all at once. Sorting data simply sorts the area parameter data so that media movement can be minimized. It is much more efficient than cutting at intervals with data that forces tools to jump from point to point. Perform Automatic Pre Feed When Cut Data is Received It is possible to feed and reverse the media automatically for specified amount when the plotter receives the cutting data.

Also, the media will be unrolled from the roll before cutting when rolled media is to be used. Perform Automatic Pre Feed When Media is Set Initial Feed It can be set to automatically feed and return the length of the page when the media is loaded and the media set lever is raised. This is equal to automatically perform the "Pre Feed" to prevent the shifting of the media.

Setting Feed Speed for Pre Feed Sets the speed of media transfer during the feed media carry of auto media transfer of received cut data, leveling of the initial feed etc.

Set the feed speed to "SLOW" if the media shifts during the pre feed if the media is heavy or slippery. The cutting time in total becomes short if you set the TOOL UP SPEED to fast speed even though the speed of the tool when it is cutting lowered is set to slow speed for the hard to cut media hard or sticky. Setting the Tool Up Move "Tool up movement" is when you continuously receive tool up movement coordinate news from the computer connected to the CE and set whether to move to every coordinate in order or go directly to the last one.

Setting Regarding Interface This chapter describes setting regarding interface. Setting Interface This section describes how to set the interface. There are 4 different setting numbers. Setting will be set, and it will return to RSC setting screen.

Baud rate can be set to , , , , , , and Settings Regarding Operation Environment This chapter describes setting regarding the operation environment. One of ten languages can be selected: Turn it OFF when setting undetectable media with high transmittance. When set to "OFF", the cutting mat may be damaged.

It may not feed properly if the media is thin, so decrease the suction force. Settings of Controls from Computer This chapter describes setting regarding the controls from the computer. Match the setting to the used software, or set it to AUTO. Supplement Automatic detection of the command may make mistake depending on the data. It will give error or malfunction when it has made mistake. All the tool condition that is received from the computer will be ignored, and only the setting and change of the tool condition from the control panel is accepted when MANUAL is selected.

Match the setting value of the application to be used. In this case, set the ": This function set the operation upon receipt of the "W" command for the drawing of arcs. The reply will be when set to , and when set to Maintenance This chapter describes the settings for the maintenance.

Never use thinner, benzene, alcohol, or similar solvents to clean the casings; Plunger Cutter blade Plunger-cap Hole Operation Be sure to clean the cutter pen regularly and remove build up. Cleaning 1 Please clean off paper dust and media build up from the When the tip of the cutter plunger gets worn down, cut quality suffers. When the tip of the plunger cap gets worn down, it is recommended that you exchange the cutter plunger.

Troubleshooting Refer to this chapter if you feel something is wrong, or it does not work right. It also describes the settings of the plotter, confirming the cutting data, and method to create test patterns. AC line inlet and the electrical outlet.

Check that the power is supplied to the electrical outlet. Contact your Graphtec customer center if the problem still exists. The plotter is defective. Move the position of the light source. There may be defective in the Contact your sales representative or operation of the media set the Graphtec call center.

Noise came in when the computer was Configure to drive the plotter from the menu turned on. The configuration regarding the output device in the application software has changed. Perform following if these are the cause of the problem. Error 15 has occurred. E Interface buffer memory has overflowed. Set the RSC transmission condition. E It is over the setting range of the distance Reset to smaller value.

E Failed to adjust the sensor level. This media cannot be used. Check the print position detecting the registration mark. E It has exceeded detection area while Check the media. Contact your sales representative or the to E Graphtec call center.

E The plotter is defective. Contact your sales representative or the Graphtec call center. Move the object disturbing the operation, Load on the motor was too large. Do not use heavy media. W When panel cutting is on, copy and origin point settings cannot be changed. The tool carriage will start moving, so there is a chance of injury.

Supplement Message to confirm tool position is displayed. Tool carriage will start to move immediately after selecting to plot the test pattern.

Supplement Plotting of the test pattern starts. It is used to check if the transmission of cutting data is performed correctly. Tool carriage will start to move immediately after selecting to print the dump list. Supplement Diagnostic test can be performed only right after the power is turned on. Messages for testing are displayed on the screen.

It will return to TEST menu screen once all the test items are completed. Appendix This chapter describes the specification of the plotter. Varies depending on the type of Graphtec-authorized film and the cutting conditions. The accuracy of minimum media width is when the push rollers are set to 5 mm from both edges of media. Specifications are subject to change without notice.

Page of Go. CE Page 19 - Front View: CE Page 20 - Rear View: CE Page 21 - Front View: CE Page 22 - Rear View: Page - Positioning of the Media and the Registr Page - Position of the Origin Point and the Reg Page - when user or standard modes are selected Page - Setting Offset Between the Registration Page - Adjusting for the Registration Mark Scan Page Page Page - Setting the registration mark automatic Table of Contents Add to my manuals Add.

Page 3 Use of the plotter in such a condition may result in a fire hazard or electric shock. Page 4 Use of a damaged cord may result in electric shock or a fire hazard due to current leakage. Page 10 Selecting a Power Cable Be sure to refer to the following tables if you wish to use a cable other than the one supplied as an accessory.

Table Of Contents Chapter 9: Setting Regarding Interface Setting Interface Page 15 Chapter 1 Product Summary This chapter explains how to connect this device your computer. Nomenclature Nomenclature Front View: Assembling Assembling Assemble the stand. Page 25 3 Attach a media stocker to each of the left and right stand side bars with two socket head cap screws, using the Allen wrench.

Page 27 3 Attach a media stocker to each of the left and right stand sides with Five socket head cap screws, using the Allen wrench. Page 29 Mounting CE 1 Set one stopper in the stock shaft. Connecting To The Computer Please install driver software before connecting. Page 31 Chapter 2: Blade Application And Features Blade Application and Features Referring to the blade application and features in the table below, select the optimal cutter blade and medium to be cut.

Page 37 3 Pulled from the front, the roll media should be long enough so that its tip completely covers the sensor. Page 38 5 Pull the media taut to make sure that there is no slack in the conveyance path, and then raise the media set lever to lower the push rollers. Page 40 3 Push the tip of the roll media forward from the back of the CE Page 41 5 Position the media and the push rollers to correspond with the width of the media.

Page 42 When Feeding Long-axis Media at exceeds 2 meters Position the push rollers at least 15 mm inside the edges of the media. Page 43 8 When the set lever is up and the media is held down by the Supplement push rollers and the media stopper is unlocked, pull out the Dirt from the floor may stick to the media when roll media and give it slack. Page 45 3 Position the media and the push rollers to correspond with Supplement the width of the media. Page 47 3 Position the media and the push rollers to correspond with Supplement the width of the media.

Page 48 5 You can set the media straight by stacking media you pull out and matching the edges up together. Page 50 When Feeding Long-axis Media at least 2 meters Position the push rollers at least 5 mm inside the edges of the media. Page 60 2 After the media is detected, the plotter is ready to receive Supplement data for cutting or plotting. Selecting Tool Condition 2. Setting The Tool Condition Setting the Tool Condition This section describes how to make the tool, speed, force, Supplement acceleration, and tool number settings.

Setting The Tool Setting the Tool Set the type and offset value of the tool that is used in each of the tool condition numbers. Setting The Speed Setting the Speed Set the speed of the tool that is used in each of the condition numbers.

Setting The Force Setting the Force Set the cutting force that is used in each of the condition numbers. Setting The Acceleration Setting the Acceleration Set the acceleration of the tool that is used in each of the tool condition numbers. Adjust The Blade Length Manually Adjust the Blade Length Manually Optimal cut is not achieved unless the blade length is adjusted in accordance to the used media and the cutter blade. Brush blade made of special steel.

Ideal for thinning and clearing tough, matted grass and scrub. Also the pruning of thorn hedges. For use with universal protection. Perfect transport protection for the engine housing of brushcutters and clearing saws. For FS 38 - FS Excellent protection against flying cuttings or stones. With or without an apron for mowing heads. We use cookies to ensure that we give you the best experience on our website.

If you would like to learn more about the usage of cookies please click here. Petrol brushcutters for landscape maintenance. FS Powerful professional brushcutter General.

Anti-vibration system Intense vibration at the handles of power tools can lead to long-term effects on blood vessels in the hands and arms. Bike handle When used in conjunction with a harness, the bike handle enables a smooth mowing action. Tool free handle adjustment The central wing nut enables easy adjustment without the use of tools. Manual fuel pump Purger A small fuel pump delivers fuel to the carburettor at the touch of a button.

Compensator This controller in the carburettor prevents the fuel-air mixture getting richer as the air filter becomes clogged. Goggles It is important to protect your eyes from flying particles and harmful UV radiation.

TrimCut mowing head Double line, for mowing and thinning work. Versions TrimCut , 2. SuperCut mowing head 2 line Double line, for mowing and thinning work. Versions Mowing line SuperCut Note and compare. Grass cutting blade 4 blades Made of steel.

Versions Grass cutting blade mm 4 blade Note and compare. Grass cutting blade 8 teeth Made of steel with 8 teeth for mowing thick, dry grass and reeds. Versions Grass cutting blade mm 8 teeth Note and compare. Grass cutting blade 40 teeth Grass cutting blade with forty teeth. For mowing tough grass. Versions Grass cutting blade mm 40 teeth Note and compare. Brush knife Brush blade made of special steel.

Written by 

Related Posts